3 inch (76mm) Lift Kit with Camber Adjusters for 1997-2001 Honda CR-V
Our steel spacer lift kit is designed to work with your factory Honda suspension (struts & springs) to acheive as much as 3 inches (76mm) of lift. Complete kit includes: 4 spacers (2 front & 2 rear), 2 adjustable rear upper control arms, 2 adjustable front upper ball joints, hardware and detailed illustrated installation instructions. This kit cannot be used with an existing lift.
Please contact tech support at 844-HRG-LIFT before ordering if you are running OME springs or, a similar lift. We will help you get the right kit to fit your needs. Our kits are powdercoated for a durable, attractive finish and use zinc plated grade 10.9 hardware.
Please check out our store for more. For off road use only! +1.25 225/70/15 (27.4") +1.5 215/75/15 (27.7").
+2.5 235/75/15 (28.8") +3.5 30x9.50R15 (30"). Lift chart for 1.5 inch spacers. Front: Approximately 3 inches of lift (included in this kit). Rear: Approximately 1.75 inches of lift. Lift chart for 2.5 inch spacers.Rear: Approximately 3 inches of lift (included in this kit). Q: How is the amount of lift measured? A: The amount of actual lift is measured from the fender lip to the ground. Q: What size tires can I run on my CRV after installing this lift kit?
A: You can fit a 215/75/15 with minor adjustment to the pinch weld in the back of the front fender. You can fit 235/75/15 tire with some trimming of the plastic. A 30+" tire will require a 4" lift or significant trimming to fit. We also recommend wheels with lower offset (backspacing) or wheel spacers to add clearance for the larger tires. Q: Will I need an alignment after installing this kit?
A: Yes, just as if you lowered your car, lifting changes the wheel alignment. It is also recommended to install camber correction kits for lifts greater than 1. Q: Will lifting my car affect the axles? It depends on the amount of lift and the type of axles you have in your vehicle. Worn original or parts store rebuilt axles are more prone to having issues. This kit is designed to solve the axle issues common to lifting the 97-01 CRV. However, lift heights can vary depending on the condition of the existing suspension and therefore we cannot guarantee there will be no axle issues. For best results, install new axles and do not combine this kit with lift springs or other spacers. Q: Do I need to replace my suspension bushings when installing a lift kit?A: It depends on the condition of your existing bushings. We always recommend inspecting your factory bushings and replacing them with urethane bushings such as Energy Suspension if needed. The added benefit of installing urethane bushings is that it allows the suspension to move more freely.
We also recommend replacing sway bar end links on 97-01 CRV after 100k as they tend to rattle when going over bumps. A: In most cases, yes. By lifting the suspension you are effectively raising the roll center of the car, which can cause additional body roll.
Our lift kits are intended for off-road use where suspension travel and ground clearance are more important. The item "3 inch (76mm) Lift Kit with Camber Adjusters for 1997-2001 Honda CR-V" is in sale since Monday, March 11, 2019. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Suspension & Steering\Lift Kits & Parts". The seller is "hrgengineering" and is located in Mooresville, North Carolina.This item can be shipped to United States, Canada.
- Drive Type: 4WD or 2WD
- Country/Region of Manufacture: United States
- Lift Height: 3 inches Front and Rear
- Type: Kit
- Manufacturer Part Number: HRG-RD1LK3.2
- Part Type: Suspension Lift Kit
- Included Hardware: Mounting Hardware
- Placement on Vehicle: Front
- Brand: HRG Engineering
- Fitment Type: Performance/Custom
- Warranty: Lifetime